|
|
ASQUITH
|
OD1 | ASQUITH OD1 4ft 6in RADIAL ARM DRILL
5MT spindle, speeds 42 – 1130 RPM, dead stop unit, 36in x 42in x..
|
- |  |  |
KITCHEN AND WALKER
|
E3 | KITCHEN AND WALKER E3 5FT RADIAL ARM DRILL
5 MT spindle, speeds 12 – 1000 RPM, read stop, coolant, lo-volt lighting,..
|
- | |  |
KITCHEN AND WALKER
|
E2 | KITCHEN AND WALKER E2 4’6” RADIAL ARM DRILL
4MT, raiser block fitted into the column, Speeds 25 – 1560 RPM, power..
|
1982 | |  |
KITCHEN AND WALKER
|
E2 | KITCHEN AND WALKER E2 4'6" RADIAL ARM DRILL
4MT, Speeds 25 – 1560 RPM, power locking, 36" x 20" x..
|
- | |  |
DONAU
|
DR32 | DONAU DR 32 RADIAL ARM DRILL
Speeds 41 - 1800 RPM, power elevation, power down feed to 4MT quill, power..
|
- | |  |
CASER
|
F35 | CASER Radial Drill
Type:F35
Table size:750x550mm
Maximum distance spindle to column:1200mm
Column diameter:305mm
Vertical travel of spindle:305mm
Spindle taper:#4 MT
Spindle speed(12):64-2100
Approx. weight:2500kg..
|
- |  |  |
CASER
|
F35A | CASER Radial Drill
Type:F35A
Year:
Drilling in the full:35mm
Drilling with pilot hole(D/2):60mm
Thread:35mm
Max. radius of drilling:1125mm
Max. distance between pin and base:1350mm
Bore:85mm
Column diameter:250mm
Spindle motor:3,5-3hp
Rotational speed(14):47-2120rpm
Machine..
|
- | |  |
ASQUITH
|
PORTABLE RADIAL | ARM LENGTH 72”
SPINDLE TAPER 6 MORSE
Machine in excellent condition, feeds to spindle, fully run and checked. ..
|
- | |  |
CSEPEL
|
RF 31B | MAKE CSEPEL
MODEL RF 31B
ARM LRNGHT 2000 mm
MORSE TRAER MT 4
SPINDLE SPEED Up to 1900 RPM
PLUS HYDRAULIC CLAMPING
BOX TABLE
FULLY WORKING MACHINE
..
|
- | |  |
MAS
|
VO 63 | TYPE RADIAL
BORING CAPACITY mm 63
TAPER CM-6
TRANSMISSION GEARS
MAIN MOTOR POWER Kw. 10..
|
- |  |  |
VOEST-ALPINE
|
UNKNOWN |
TYPE RADIAL..
|
- | |  |
ASQUITH
|
ASR 36” | Asquith ASR 36” radial arm drill with rise and fall table, 3 morse taper and spindle brake..
|
- | |  |
RICHMOND
|
SR2 | Richmond SR2 40” radial arm drill 3 morse taper with rise and fall table and spindle brake. Very quiet runner..
|
- | |  |
ASQUITH
|
OD1 | Asquith OD1 4’6” radial arm drill,5 morse taper,box table,spindle brake,coolant,rewired.Very nice example,runs well...
|
- | |  |
KOLB
|
* | bore capacity in steel (diameter) 80mm
arm length 1.600mm
workpiece height max. 950mm
distance spindle/base plate 600/ 1430mm
distance between table/spindle 100/ 950mm
total power requirement 6,1kW
weight of the machine ca. 2,5t
dimensions..
|
- |  |  |
STANKO
|
2 M 55 | RADIAL DRILLING MACHINE
Taper : 5 mk
Drilling capacity : 55 mm
Throat, max : 375 - 1.600 mm
Distance, spindle - floor plate : 450 - 1.600 mm
Floor plate dimensions : 1.650 x 825 mm
Drilling depth : 400 mm
RPM spindle..
|
1981 |  |  |
STANKOIMPORT
|
2H57 | bore capacity in steel (diameter) 75 mm
arm length 2500 mm
workpiece height max. 1600 mm
tool taper 5 MK..
|
1967 | |  |
CSEPEL
|
RF31-C | bore capacity in steel (diameter) 60 mm
arm length 1750 mm
workpiece height max. 2000 mm
spindle turning speed range..
|
1969 | |  |
ASQUITH
|
6 PT 19-72 | RADIAL DRILLING MACHINE
Taper : 6 Mc
Throat : 1.600 mm
Drilling capacity, steel, full material : 63 mm
Drilling capacity, iron, full material : 80 mm
Drilling depth : 430 mm
Height between spindle - feet, min. - max. : 750 -..
|
- | |  |
WMW HECKERT
|
BR 40/2×1250 | Maximum drilling diameter 60 mm
Maximum spindle stock travel 1250 mm
Maximum workpiece height 1380 mm..
|
- |  |  |
ARCHDALE
|
RADIAL | Table Area: 600mm x 900mm
Main Drive Power: 415volts/3 phase
Spindle Speeds: 15 to 1500 rpm
Spindle Taper: MT5
Radius..
|
- | |  |
MAS
|
VR4A | Taper : 4 mc
Troath depth : 1.150 mm
Drill capacity : 45 mm
Depth of hole : 300 mm..
|
- | |  |
OTTO-MÜLLER
|
SR 23 | bore capacity in steel (diameter) 23 mm
arm length 1020 mm
workpiece height max. 400 mm
bore capacity in cast..
|
1984 | |  |
OTTO-MÜLLER
|
SR23 | bore capacity in steel (diameter) 23 mm
arm length 1020 mm
workpiece height max. 400 mm
bore capacity in cast..
|
1988 | |  |
ASQUITH
|
NC 3A5 | YEAR 1975;TABLE 84X42; X=56INCH; Y-34INCH; 72INCH B-C; 10TO 2000 RPM; FEED RATE .006 TO .045; VERY GOOD CLEAN MACHINE IN..
|
1975 | |  |
MODIGS
|
MODIGS | Feeds: Yes
Throat: 590mm
Max Drilling Capacity: 11/2\"
Table Area: 450mm x 450mm
Main Drive Power: 415 volts
Spindle Speeds:..
|
- | |  |
DONAU
|
DR 23 | bore capacity in steel (diameter) 23 mm
arm length 995 mm
workpiece height max. 450 mm
bore capacity in cast..
|
1971 | |  |
HMT
|
RM63/1400 | Maximum boring diameter 50 mm
Maximum spindle stock travel 1400 mm
..
|
- | |  |
POLLARD
|
15X | Drilling Machine - Pillar 4 morse
Column Diameter: rise & fall
Feeds: no
Table Area: rise & fall
Spindle Speeds: 84-1465..
|
- | |  |
MOSTANA
|
MOSTANA | Max Workpiece Height (Spindle to Base): 18"
Spindle Taper: MT5
Elevating Arm / Table / Portable / Unive: Elevating..
|
- | |  |
MEDDINGS
|
A10 | Radial Drill - Articulated Arm No. 2 Morse Taper
Feeds: Manual
Max Drilling Depth: 100
Max Workpiece Height: 500
Max Travel..
|
- | |  |
RICHMOND
|
SR2 | Radial No 3 MT x 36" Radius
Max Workpiece Height: 26"
Max Travel Of Drilling Head On Slide: 25.1/2"
Max Drilling..
|
- | |  |
QUARTERS-SMITH
|
QSR2 | Max Travel Of Drilling Head On Slide: 390mm
Throat: 740
Max Drilling Capacity: 32mm
Table Area: 530 x 450mm
Main..
|
- | |  |
MEDDINGS
|
A10 | Articulated Arm No. 2 Morse Taper
Feeds: Manual
Max Drilling Depth: 100
Max Workpiece Height: 500
Max Travel Of Drilling..
|
- | |  |
ARCHDALE
|
ARCHDALE | Spindle Taper: No 4
Radius Of Arm: 3ft 6"
..
|
- | |  |
NOVISA
|
TR 1300 | Radial drill NOVISA TR 1300, drilling diameter 40 mm, length of arm 1.300 mm, with box table, power locking..
|
- |  |  |
ITAMA
|
T 40/900R | Radial drill ITAMA T 40/900R, drilling diameter 40 mm, length of arm 900 mm, with box table...
|
- | |  |
INVEMA
|
FR 40 1250 | Radial drill INVEMA FR 40 1250, drilling diameter 40 mm, length of arm 1.250 mm, with box table.
..
|
- | |  |
CMEC
|
Z 3025 X 10 | Radial drill CMEC Z 3025 X 10, drilling diameter 25 mm, length of arm 1.000 mm, with box table.
..
|
- | |  |
CASER
|
35-915 | Radial drill CASER 35-915, drilling diameter 35 mm, length of arm 915 mm, with box table.
..
|
- | | - |
CARIMATI
|
CTU 35/45I | Radial drill CARIMATI CTU 35/45, drilling diameter 45 mm, length of arm 1.250 mm, with box table...
|
- | |  |
BREDA
|
R 950 MS | Radial drill BREDA R 950 MS, drilling diameter 40 mm, length of arm 950 mm, with box table...
|
- | |  |
BREDA
|
R 915 L | Radial drill BREDA R 915 L, drilling diameter 40 mm, length of arm 915 mm, with box table...
|
- | | - |
BREDA
|
R 60-2000 | Radial drill BREDA R 60-2000, drilling diameter 60 mm, length of arm 2.000 mm, with box table, power locking..
|
- | |  |
BREDA
|
R 1580 MP | Radial drill BREDA R 1580 MP, drilling diameter 50 mm, length of arm 1.600 mm, with box table, power locking.
..
|
- | |  |
ELLIOTT
|
- | Drilling Machine - Radial Arm No 4 morse taper x 36\"
Table Area: 30" x 20" x 20" Box
Spindle Speeds:..
|
- | |  |
KITCHEN-WADE
Auction item |
E32-MK2 | Radius of drill spindle (max) 1372 mm, Radius of drill spindle (min) 406 mm, Traverse of head along arm 1372..
|
1974 | |  |